Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
- 10. Brake system
   10.1.2. Brake Pads forward brakes
   10.1.3. Brake Pads back brakes
   10.1.4. The general adjustment of back brakes (Girling)
   10.1.5. Replacement brake колодок (all-wheel drive models)
   10.1.6. The general adjustment of back brakes (Girling) (all-wheel drive models)
   10.1.7. Plugs of pedals of a brake and coupling
   10.1.8. Adjustment of a manual brake
   10.1.9. Removal of the lever of a manual brake
   - 10.2. Hydraulic components
      10.2.1. The hydraulic booster of brakes / the main brake cylinder
      10.2.2. Changes in hydraulic system
      10.2.3. The main brake cylinder / сервоцилиндр brake system
   + 10.3. Antiblocking system of brakes
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment


выделения на 19 неделе беременности - поставим диски тормозов на хонда с гарантией



10.2. Hydraulic components
THE GENERAL DATA

Support of a forward brake – Girling

1. Dustproof
2. The piston
3. A dustproof ring
4. An arm brake колодок
If protective caps have been damaged, establish the repair complete set, a detail 443 698 470
Grease directing pins with applied greasing
5. A piston epiploon
6. A support
7. 35 Н.м.
Always replace
At untwisting / a twisting keep directing pin a key with накидной a head
8. The screw of an aperture of release of air

At repair use all elements of a repair set.

Support of a forward brake – Teves

1. A directing pin
The inhaling moment: 25 Н.м.
2. The screw of an aperture of release of air
3. A support
4. A piston epiploon
5. A dustproof cover
6. The piston
7. An arm brake колодок
8. The rubber plug
9. The plug
10. A dustproof cap
11. A cap

At repair use all elements of a repair set.


The prevention

Before installation grease epiploons and pistons of supports with greasing VW of the brake cylinder or similar to it.


Support of a back brake – Girling

1. Самоконтрящиеся bolts.
The inhaling moment: 35 Н.м.
Always replace
Keep directing pins at a twisting and untwisting
2. A support
Replace a support if it proceeds in an installation site of the lever of a manual brake
3. A piston epiploon
4. The piston
5. A dustproof ring
6. An arm brake колодок
If protective caps have been damaged, establish the repair complete set, a detail 443 698 470
Grease directing pins with applied greasing
7. A protective cap
8. A directing pin
Grease before installation of a protective cap
9. The screw of an aperture of release of air
10. A dustproof cap

At repair use all elements of a repair set.

New supports of brakes are on sale filled with a brake liquid and pumped over.

Grease pistons and cylinders of supports, and also epiploons with a thin layer of a liquid of the brake cylinder before installation.

Support with two pistons – for all-wheel drive and models with 20 клапанными engines, and also compartment models

1. The screw of an aperture of release of air
Grease a screw carving with a thin layer of a liquid of the brake cylinder before installation
2. 35 Н.м.
3. A support
4. A directing pin
Grease before cap installation
5. A cap
Fastens to an arm колодок and to directing pin
6. An arm brake колодок
Grease directing pins with applied greasing
If protective caps have been damaged, establish the repair complete set, a detail 443 698 470 which is on sale as the spare part with preliminary greased directing pins
7. A dustproof ring
Put on external edge the piston
The internal edge is established in a flute on a support
8. The piston
9. A piston epiploon
10. A dustproof cap

At repair use all elements of a repair set.


The prevention

Before installation grease epiploons and pistons of supports with greasing VW of the brake cylinder or similar to it.