Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. A steering
   11.2. A shaft and a casing of a steering column
   11.3. A power absorbing steering column
   11.4. A steering drive
   11.5. The pipeline of high pressure / the return pipeline
   11.6. Free wheeling adjustment рейки a steering
   11.7. A klinovoj belt
   - 11.8. System of hydrostrengthening of a steering
      11.8.1. Technical characteristics
      11.8.2. Prorolling / filling of a hydraulic liquid
      11.8.3. Check on tightness (at the working engine)
      11.8.4. Steering transfer
      11.8.5. The pump of the hydraulic booster of a steering (Vickers)
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment





11.8.4. Steering transfer
THE GENERAL DATA

Steering transfer with the hydraulic booster, models since МА 054 850 (the Sedan with 5-tsillindrovym the engine) – 8А МА 002 645 (an all-wheel drive Compartment)

1. The case рейки
2. An epiploon рейки*
3. A lock ring
It is possible to remove / to establish only after removal рейки
4. A fixing ring
Put on on рейку a steering against the stop 
Establish a cover on a flute passing on a circle of a ring
5. A cover
It is possible to replace, without removing реечный the steering mechanism
6. A collar
Use a collar which is pulled together by means of the screw, the screw should be turned to a body
7. A sealing ring, always replace
8. The adjusting screw
9. 20 Н.м.
10. A cover
11. A sealing ring
35x2.5
Always replace
It is established in a flute on the case
12. A sealing ring
27x2.5 mm
Always replace
It is established in a plug flute
13. The plug
14. A kompressionnaja spring
 It is established in a toddler
15. A toddler
16. A washer

17. 20 Н.м.
18. A casing of a leading gear wheel
19. An epiploon
 Always replace
20. A washer
21. Штифт*
2.5x6 mm
Always replace
Pull out a pin by means of flat-nose pliers before removal of a casing of a leading gear wheel
22. A leading gear wheel / the ring valve
23. A sealing ring
9x2 mm
24. A sealing ring
25. A cover
The inhaling moment: 50 Н.м.
Tighten by means of two кернеров established at an angle in 180 ° to each other
26. A fixing ring
Always replace
27. A sealing ring
44x2.5 mm
Always replace
28. Рейка a steering
For removal: turn off a cover and pull out рейку on the left side of the case
Check up рейку on presence of scratches round an epiploon installation site

All elements marked with an asterisk, are included in the repair complete set and should be replaced during repair.

The prevention

The system of hydrostrengthening of a steering is filled by a hydraulic liquid, detail G 002 000.

Works with a steering drive should be spent on a pure place and all elements should contain in absolute cleanliness.


Steering transfer for Compartment model

1. A washer
2. 35 Н.м.
3. 45 Н.м., always replace
4. 45 Н.м., always replace
5. The adjusting screw
6. 40 Н.м., at removal, keep a head демпферной plugs by means of a wrench
7. An arm
8. The plug with a carving, is a part демпферного the steering mechanism
9. The dempfernaja plug, remove before removal рейки and an arm








бизнес иммиграция в сша