Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A plug - the main cylinder of coupling
   8.1.3. Press a coupling disk
   8.1.4. Malfunctions of coupling
   + 8.2. A mechanical transmission 012
   + 8.3. A mechanical transmission 01А
   + 8.4. An automatic transmission 089
   - 8.5. An automatic transmission 087
      8.5.2. The lever and a rope of the lever of a gear change
      8.5.3. The mechanism of management throttle заслонкой
      8.5.4. Removal and transmission installation
      8.5.5. Check of the moments of a gear change
      8.5.6. The main transfer
   8.6. Dismantling and assemblage of automatic transmissions
   8.7. The block of valves
   + 8.8. An automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment





8.5.2. The lever and a rope of the lever of a gear change
THE GENERAL DATA

The mechanism of the lever of a gear change and gear change rope

1. 3 Н.м.
2. A cover
3. The electromagnetic switch
4. A torsionnaja spring
5. 5 Н.м.
6. The plug
7. A washer
8. The switch of the lever of a gear change
Check
The engine should be started, when the lever
Switchings is in position Р or N
Backing headlights should light up at inclusion of transfer of a backing
If is not present, turn the switch in a nest and again check up its work
9. The basis
At installation put a layer of hermetic АКD 512 001 between the basis and a body
10. A clip bolt
11. A cartridge
12. A washer
13. Муфта
14. The plug
15. Кроншейн
16. A lock ring
17. A rope of the lever of a gear change
With directing and the plug
Grease the rope ends before installation
Tighten a nut of fastening of a rope on an arm
To 15 Н.м.
Check up, that the directing tube densely sat
Move the gear change lever
In position Р (against the stop back)
Tighten a nut of a clip of a rope to 20 Н.м.

18. 23 Н.м.
19. A cover
If necessary, replace
Check up accuracy of its installation that the moisture has not got on a gear change rope
20. Муфта
21. A washer
22. 20 Н.м.
23. The switching lever
24. A washer
25. A spring clamp
26. The plug
27. A washer
28. A compression spring
Establish on the lever of switching before installation of a directing pin
29. A directing pin
30. The switching lever предач
With a plug for lever lock-out in position Р or N
31. A lever casing преключения transfers
It is established by designation P forward
Establish after регупировки the electromagnetic switch
32. The handle of the lever of a gear change

Installation of an arm of the lever of a gear change in relation to the gear change lever

PERFORMANCE ORDER
1) establish probe And, thickness of 1.0 mm, between the lever of a gear change and the electromagnetic switch
2) move the gear change lever in position R, press the electromagnetic switch to probeу and tighten a nut of fastening to 10 Н.м.
3) after installation of the electromagnetic switch, establish on the centre the bottom aperture of a plug of the lever of a gear change and submit pressure on the switch
4) the solenoid pin will close a plug
5) establish a casing of the lever of a gear change so that the gear change lever was opposite to mark N in a casing (neutral transfer);
The gear change lever should pass identical distance between positions N and D and positions N and R
6) establish the lever And by means of a pin or a drill

In = the Pin, diameter 4.0 mm, inserted into a casing aperture
7) switch the gear change lever in position in position N
8) establish the switch so that fastening (it is specified by an arrow) was fixed on the gear change lever
9) tighten bolts of fastening to 5 Н.м.

10) remove a pin or a drill

After switch installation, check up its work.